List of products by brand Valsteam ADCA

Condensate Pumps

ADCA - Pump trap - APST

The ADCAMat APST automatic pump trap is especially recommended where stall condition may occur due to poor steam trap condensate discharge capacity, caused by temporary insufficient pressure drop. The equipment combines the features of a float steam trap and a pressure operated pump, in one single unit.

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel

Condensate Pumps

ADCA - Pump trap - POP DN 100

The ADCAMAT POP (Pressure Operated Pump), fabricated in carbon steel (stainless steel on request), is recommended in the transfer of high-temperature liquids such as condensate, oils and others, to a higher elevation or pressure. Under certain conditions, it can drain a closed vessel under vacuum or pressure. The pump can be operated by steam, compressed...

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel

Condensate Pumps

ADCA - Pump trap - POP DN 25-80

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel

Condensate Pumps

ADCA -Pump trap - POP-CT

The ADCAMat POP-CT stroke counter is designed to monitor the operation of pressure operated pumps in open vented systems. The device is mechanical and operates by change in pressure inside the pump which it is connected to. It can be used to determine the amount of condensate return and establish maintenance intervals.

View

Condensate Pumps

ADCA - Pump trap - POPS-LC

The ADCAMat POP-LC low capacity pressure operated pump is recommended in the transfer of steam condensate, oils and other non-hazardous liquids compatible with the construction, to a higher elevation or pressure. Under certain conditions, it can drain a closed vessel under vacuum or pressure.The pump can be operated using steam, compressed air or other...

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel

Condensate Pumps

ADCA - Pump trap - PPA14

The ADCAMat PPA14 pressure operated pump is recommended in the transfer of steam condensate, oils and other non-hazardous liquids compatible with the construction, to a higher elevation or pressure. Under certain conditions, it can drain a closed vessel under vacuum or pressure. The pump can be operated using steam, compressed air or other gases, and is...

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel

Condensate Pumps

ADCA - Pump trap - PPA312

The ADCAMat PPA312 pressure operated pump is recommended in the transfer of steam condensate, oils and other non-hazardous liquids compatible with the construction, to a higher elevation or pressure. Under certain conditions, it can drain a closed vessel under vacuum or pressure. The pump can be operated using steam, compressed air or other gases, and is...

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel

Condensate Pumps

ADCA - Pump trap - PPT14

The ADCAMat PPT14 automatic pump trap is especially recommended where stall condition may occur due to poor steam trap condensate discharge capacity, caused by temporary insufficient pressure drop. The equipment combines the features of a float steam trap and a pressure operated pump, in one single unit.

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel

Condensate Pumps

ADCA - Pump trap - PPΟ14

The ADCAMat PPO14 pressure operated pump is recommended in the transfer of steam condensate, oils and other non-hazardous liquids compatible with the construction, to a higher elevation or pressure. Under certain conditions, it can drain a closed vessel under vacuum or pressure. The pump can be operated using steam, compressed air or other gases, and is...

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel

Tubular Heating Exchangers

ADCA - Adcatherm Heat Exchangers - R SERIES

The ADCA R series steam to water tubular heating coils are shorter and lighter than the alternative tubular heating coils manufactured with smooth pipes. The use of extruded low fin tube has the advantage that it can improve the external surface and thermal performance.

View

Shell and Tube Exchangers

ADCA - Adcatherm Heat Exchangers - STH

The ADCA ST series steam to water shell and tube heat exchangers are shorter and lighter than the alternative shell and tube exchangers manufactured with smooth pipes. The use of extruded low fin tubes has the advantage that it can improve the external surface and thermal performance.

View

Shell and Tube Exchangers

ADCA - Adcatherm Heat Exchangers - STS

The ADCA STS series steam to water shell and tube heat exchangers are shorter and lighter than the alternative shell and tube exchangers manufactured with smooth pipes. The use of extruded low fin tube has the advantage that it can improve the external surface and thermal performance.

View

BSP NPT Flanged PN 16 150 lbs DIN ANSI 1.4404

Shell and Tube Exchangers

ADCA - Adcatherm Heat Exchangers - STV

View

NPT Flanged ISO 7 Rp PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel

Deaerators

ADCA - Deaerator - ADG

The ADCATherm atmospheric semi-deaerators are designed to heat boiler feed water and to reduce oxygen and carbon dioxide (oxygen values in the feed water of less than 1,6 mg/L can be achieved). Remaining oxygen can be completely removed using oxygen-scavenging chemicals. Basically, the complete system consists of a storage vessel, a deaeration head...

View

Blowdown Vessels

ADCA - Boiler House Equipment - BEX

The ADCA BEX series blowdown expansion and cooling units are used in modern boiler houses to cool hot waste water and steam boiler blowdown before discharging them into a pit or drain.

View

NPT Flanged PN 16 150 lbs DIN ANSI Carbon Steel

Complementary Equipment

ADCA - Boiler House Equipment - BFT

The BFT boiler feed tank is one of the most important devices in a boiler room. Its main function is to store the make-up water and condensate, assuring a reserve of treated water to supply to the steam boilers. The make-up water has to be softened to prevent scale formation on the boiler and the oxygen also has to be removed, so that corrosion in the...

View

Blowdown Vessels

ADCA - Boiler House Equipment - BV

The ADCA BV series blowdown vessels are used in modern boiler houses to cool hot waste water and steam boiler blowdown before discharging them into a pit or drain. If flash steam can not be recovered or discharged to the atmosphere, an optional condensing water spray system can be supplied. It is fitted into the top of the unit and can be controlled by a...

View

Flanged PN 16 DIN Carbon Steel Stainless Steel

Complementary Equipment

ADCA - Boiler House Equipment - FCD

The ADCA flash condensing heads are designed to promote energy efficiency on new or existing systems. Mixing the flash steam with the boiler make-up water allows the energy within the flash steam to be fully absorbed into the water and therefore reduces energy waste that normally occurs from the discharge of flash steam through a vent.

View

Flash Vessels

ADCA - Flash Vessel - RV

The flash vessel is the main component in any flash recovery system. It can be used in all steam plants where high pressure condensate is reduced to a lower pressure, so that flash steam is formed by reevaporation. This steam can be used in low pressure process or heating equipments.

View

Flanged PN 16 DIN Carbon Steel Stainless Steel

Flash Vessels

ADCA - Flash Vessel - RVST

The flash vessel is the main component in any flash recovery system. It can be used in all steam plants where high-pressure condensate is reduced to a lower pressure, so that flash steam is formed by re-evaporation. This steam can be used in a low pressure process or heating equipment.

View

Flanged PN 16 DIN Carbon Steel Stainless Steel

Deaerators

ADCA - Deaerator - TDG

The TDG series tray-type thermal deaerators are designed to heat boiler feed water and reduce oxygen and carbon dioxide levels (oxygen levels in the feed water of less than 0,02 mg/l - 0,02 ppm can be achieved). Remaining oxygen can be completely removed using oxygen-scavenging chemicals. Basically, the complete system consists of a storage vessel, a...

View

Humidity Separators

ADCA - Humidity Separators - AS

The AS series centrifugal air and dirt separators were designed to be used in the flow line of a hydronic heater or cooling system. The operation is based on the principle of centrifugal force, instead of relying on low-velocity separation, offering the advantage of efficient separation in a smaller vessel. The ADCA AS units provides maximum separation...

View

Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel Stainless Steel Galvanized Steel

Complementary Equipment

ADCA - Complementary Equipment - EH

The EH series exhaust heads were designed to protect personnel from injury and exterior of buildings from harmful effects of steam ejection to atmosphere. The head is fitted at the end of a vertical exhaust pipe and effectively retains the moisture separated from the steam for draining.

View

Flanged PN 16 150 lbs DIN ANSI Carbon Steel Stainless Steel Galvanized Steel

Complementary Equipment

ADCA - Complementary Equipment - HCC

The HCC is a cooling device that allows the mixing of hot condensate with a lower temperature condensate, avoiding hammering. Condensate discharge from higher pressure lines (drip points, for instance) is often connected to low-pressure condensate lines, with lower temperatures. This sudden pressure drop will convert the sensible heat difference between...

View

Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel Stainless Steel

Complementary Equipment

ADCA - Complementary Equipment - LIPO

The LIPO series of condensate lifting pots are designed for installation in steam and condensate systems. They are particularly used in condensate lines where condensate must be transported without causing water hammers and noise and lifted to elevated condensate mains.

View

Flanged PN 16 PN 40 150 lbs DIN ANSI Carbon Steel Stainless Steel

Complementary Equipment

ADCA - Complementary Equipment - MLI

The MLI series of bypass type magnetic level indicators were designed for continuous level indication and/or control in ADCA ECRU units and other special SKID mounted packages. The indicators can be equipped with multiple MSB reed switches for alarm purposes or a side mounted level transmitter for continuous level monitoring.

View

Flanged PN 40 300 lbs DIN ANSI Stainless Steel

Steam Humidifiers

ADCA - Direct Steam Humidifiers - DSH

The ADCA DSH series of direct steam injection humidifiers are designed to ensure highly efficient and moisture free steam injection in air ducts and AHU for humidification purposes. These units are completely manufactured from corrosion resistant stainless steel, and are available as plug and play packaged solutions or alternatively as individual...

View

NPT Flanged ISO 7 Rp PN 16 150 lbs DIN ANSI Stainless Steel

Humidity Separators

ADCA - Humidity Separators - S16S

The S16 series centrifugal separators remove moisture from steam and compressed air pipelines. Steam and compressed air pass through the separator and, as a result of centrifugal forces, impacts and swirling effects, the particles with a heavier specific gravity, such as water and oil droplets, moisture in suspension, dirt and scale are separated from the...

View

NPT PN 16 PN 40 DIN Carbon Steel

Humidity Separators

ADCA - Humidity Separators - S16SS

View

NPT PN 16 PN 40 DIN Stainless Steel

Humidity Separators

ADCA - Humidity Separators - S25/S HV / S25/S VH

The S25 series centrifugal separators remove moisture from steam and compressed air pipelines. Steam and compressed air pass through the separator and, as a result of centrifugal forces, impacts and swirling effects, the particles with a heavier specific gravity, such as water and oil droplets, moisture in suspension, dirt and scale are separated from the...

View

NPT Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Stainless Steel

Humidity Separators

ADCA - Humidity Separators - S25S | PN16 - PN40

View

NPT Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel

Humidity Separators

ADCA - Humidity Separators - S25S | PN63

View

Flanged Socket Weld PN 63 600 lbs DIN ANSI Carbon Steel

Humidity Separators

ADCA - Humidity Separators - S25SS

View

Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel Galvanized Steel

Humidity Separators

ADCA - Humidity Separators - S30

The S30 series baffle separators remove moisture from steam and compressed air pipelines. Steam and compressed air pass through the separator and, as a result of expansion, impact and swirling effects, the particles with a heavier specific gravity, such as water and oil droplets, moisture in suspension, dirt and scale, are separated from the fluid. The...

View

NPT Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel Galvanized Steel

Humidity Separators

ADCA - Humidity Separators - SF251/S

The SF251/S series centrifugal separators remove moisture from steam and compressed air pipelines. Steam and compressed air pass through the separator and, as a result of centrifugal forces, impact and swirling effects, the particles with a heavier specific gravity, such as water and oil droplets, moisture in suspension, dirt and scale are separated from...

View

Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel

Humidity Separators

ADCA - Humidity Separators - SH25

The SH25/S series horizontal centrifugal separators remove moisture from steam and compressed air pipelines. Steam and compressed air pass through the separator and, as a result of centrifugal forces, impact and swirling effects, the particles with a heavier specific gravity, such as water and oil droplets, moisture in suspension, dirt and scale are...

View

Flanged PN 16 PN 40 150 lbs 300 lbs DIN ANSI Carbon Steel

Sample Coolers

ADCA - Sample Coolers - SC32 / SC132

The ADCA sample coolers are specially designed to cool samples of boiler water or steam for analysis. Sample coolers prevent steam flashing-off from hot pressurized liquid samples, which can be dangerous and may result in an incorrect sample. This device may be used for boiler water analysis and other sampling or cooling applications compatible with the...

View

Sample Coolers

ADCA - Sample Coolers - SC32B / SC132B

View

Sample Coolers

ADCA - Sample Coolers - SC32F / SC132F

The ADCA sample coolers are specially designed to cool samples of boiler water or steam for analysis. Sample coolers prevent steam flashing-off from hot pressurized liquid samples, which can be dangerous and may result in an incorrect water sample. This device may be used for boiler water analysis and other sampling or cooling applications compatible with...

View

Sample Coolers

ADCA - Sample Coolers - SC332 - SC532

The ADCA sample coolers were specially designed to cool samples of boiler water or steam for analysis. Sample coolers prevent steam flashing-off from hot pressurised liquid samples, which can be dangerous and may result in an incorrect sample. This device may be used for boiler water analysis and other sampling or cooling applications compatible with the...

View

Mixing Valves

ADCA - Steam - Water Mixers - MX20

The ADCAMix MX20 is a series of steam/water mixers designed to provide a cheap and instantaneous source of low pressure hot water, by using existing steam and cold water supplies. The mixer incorporates a safety device, to ensure that live steam cannot be accidentally ejected even if, for some reason, the cold water supply fails. The water temperature at...

View

Mixing Valves

ADCA - Steam - Water Mixers - SG20

The SG20 series water-saving guns are especially recommended to be used along with the Adcamix MX20 steam to water mixers. By using this gun, water and energy costs can be considerably reduced and it also contributes to environmental protection, avoiding the use of chemicals in the cleaning process.

View

Steam Injectors

ADCA - Steam Injectors - SI115

The ADCAMix SI115 is a series of direct steam injectors designed for rapid heating of still or flowing mediums, inside basins and vessels. Steam enters through the inlet connection, passes along the center of the device and mixes with the cool medium, which is drawn in through radial holes.

View

ISO 7 Rp PN 25 DIN Austenitic Stainless Steel

Steam Injectors

ADCA - Steam Injectors - SI125 / SI140

The ADCAMix SI125 and SI140 is a series of direct steam injectors designed for rapid heating of still or flowing mediums, inside basins and vessels. Steam enters through the inlet connection, passes along the center of the device and mixes with the cool medium, which is drawn in through radial holes.

View

ISO 7 Rp PN 25 DIN Austenitic Stainless Steel

Steam Injectors

ADCA - Steam Injectors - SI20

The ADCAMix SI20 is a series of direct steam injectors designed for low noise heating of still or flowing mediums, inside basins and vessels.

View

Systems/Skids

Adcamat Pumps & Pump Traps - POPS-K (Simplex)

The POPS-K packaged pump units can be used to lift or displace hot condensate and other liquids even in hazardous areas.

View

Systems/Skids

Adcamat Pumps & Pump Traps - POPS-KD (Duplex)

The POPS-K packaged pump units can be used to lift or displace hot condensate and other liquids even in hazardous areas.

View

Systems/Skids

Adcamat Pumps & Pump Traps - POPS-KT (Triplex)

The POPS-K packaged pump units can be used to lift or displace hot condensate and other liquids even in hazardous areas.

View

Showing 1-48 of 54 item(s)

One-stop shop – geared to your market

List of products by brand Valsteam ADCA